How to Install the Mira Meta Electric Shower

Friday 4th May 2018

More Articles

Let us take you through the step by step guide to install the Mira Meta Electric Shower. You can apply this installation guide to the new Mira Play and Mira Corus electric shower ranges.

After unpacking the shower familiarise yourself with the instructions. Start by ensuring that the electrical supply is off at the mains.

Meta.00_00_27_06.Still011.png

Step 1

Decide on a suitable position for the shower unit and fittings leaving adequate space for maintenance. Please note that a suitable position for the shower will have a minimum clear distance of 200 mm from the ceiling to allow for cover removal and refitting.

Step 2

Remove the three cover screws at the top and bottom of the unit and remove the cover, service tunnel and bungs.

Corus.00_00_35_20.Still003.png
Corus.00_04_18_18.Still005.png
Meta.00_00_43_20.Still013.png

Step 3

  • Determine the direction and route of the incoming water supply.
  • Add an elbow to the supply pipe and connect it as a rising or falling supply.
Meta.00_00_54_08.Still014.png
  • Complete any soldering required away from the appliance.
  • Now flush through the pipework to wash-out any debris before connection.
Meta.00_01_09_22.Still015.png

Step 4

Use the installation template provided along with a spirit level to mark the required fixing holes. Check that the wall behind the fixing holes is clear of wires or pipework using a stud detector. Then drill the required fixing holes and insert the wall plugs supplied.

Meta.00_01_13_20.Still016.png
Meta.00_01_19_18.Still017.png
Meta.00_01_25_00.Still018.png
Meta.00_01_31_02.Still019.png
Meta.00_01_37_04.Still020.png

Step 5

  • Present the appliance to the wall and affix with the supplied screws and wall plugs.
  • Check the inlet filter is in position then connect the supply pipe.
  • Turn the water supply on and check the shower unit for leaks.
Meta.00_01_41_02.Still021.png
Meta.00_01_53_15.Still022.png
Meta.00_01_58_20.Still023.png

Step 6

Strip back the outer cable insulation and insert the wires into the terminal block. Tighten the screws in the terminal block, make sure the wires are secure and tight.   

Meta.00_02_14_18.Still025.png

Step 7

 

Refit the pipe and cable blanking plates and the service tunnel. 

Meta.00_02_25_22.Still027.png

Installing the fittings

Step 8 & 9

  • Hold the slide rail assembly against the wall in the desired position, checking it is vertical with a spirit level, and use the slide rail brackets as a template to mark the positions of the top and bottom fixing holes.
  • Drill the fixing holes and insert the wall plugs provided.
  • Secure the mounting brackets onto the wall using the wall screws, check for vertical alignment then fully tighten.
Meta.00_02_33_23.Still028.png
Meta.00_02_51_18.Still029.png

Step 10

Push the clamp bracket down onto the slide rail, rotating the lever to help with installation. Push the slide bar supports onto the slide bar.

Meta.00_03_10_00.Still031.png
  • Fit the slide bar supports over the mounting brackets and adjust the slide bar vertically ensuring an equal length of the slide bar protrudes from the top and bottom mounting bracket. 
  • Carefully remove the slide bar assembly, preventing any further movement between the slide bar and slide bar supports. Tighten the two slide bar clamping screws no more than half a turn to secure the slide bar supports to the slide bar. 
  • Install the slide bar assembly onto the mounting brackets and tighten the bolts using the hex key.
Meta.00_03_17_11.Still032.png
Meta.00_03_22_04.Still033.png
Meta.00_03_26_10.Still034.png
Meta.00_03_38_23.Still036.png

 

 

Install the end cap at the top and the soap dish at the bottom of the slide bar.

Step 11

To fit the hose and shower handset, first insert a hose seal into the conical nut of the hose and screw the hose onto the outlet of the shower.

Meta.00_03_52_23.Still038.png

Feed the hose through the soap dish and insert the other seal into the other conical nut of the hose and screw onto the shower handset.

Meta.00_04_00_15.Still039.png

Finally, place the shower handset into the clamp bracket assembly and make sure that the control dials are aligned with the spindles. 

Meta.00_04_23_09.Still042.png

Watch the Video

For further support on the installation you can follow the step by step installation in our dedicated film. 

View the complete Mira Meta, Play, Corus and range here and share your installations with us on Twitter @mirashowers

play
Close Film